5/29/2011 – Porthole screens

Since we’re planning to spend our summer further north in the Sea of Cortez, we’ve been advised by many seasoned cruisers that we need adequate bug screens. Besides mosquitoes and bobos, we need to be able to keep bees and jejenes (no-see-ums) out of our living spaces. Lulu made a nice screen for our forward hatch and also included a screen in the wind scoop she made. She’s currently working on the design for a screen for our companionway. We’ve been stymied, however, by trying to come up with a way to screen our round portholes.

We’ve tossed around a lot of ideas and even tried a couple. The simplest seemed to be to just use long cable ties to attach screen to the outside of the ports. Problem was, there’s only a very small lip to attach to and it’s hard to get the screens on, especially on the ports that have the PortVisors on them. And, the end product looked ugly as all get-out.

Some round ports are made for screens and have a little groove around the inside that a screen attached to a sort of wire snap-ring fits into. However, we don’t have those grooves. I thought that the best remedy was to come up with something similar but flat, instead of round like a wire. Something that could be made smaller to fit into the opening and then would expand, holding the screen material in place. Sure, great idea, but what the heck can I use to do it?

I thought I’d hit on the perfect solution when we bought a mini-blind that we could cannibalize for the slats. Seemed like the slats would have just the right amount of spring to do the job. They didn’t. The problem with them was that they were so thin that, when I tried to form one into a circle, it wouldn’t stay circular but rather would bend into a misshapen triangle.

I toyed with the idea of having some sort of flat snap ring made out of metal, maybe stainless steel. Of course, I’d have to come up with a clear drawing of what I wanted but that shouldn’t be too hard, should it? This looked like the most promising idea yet.

Then, one night it came to me. I got up and measured the inside diameter of the ports: 6″ and 4″. What if I got some 6″ and 4″ plastic pipe? The outside diameter of the pipe would be a little larger than 6″ and 4″ so. if I cut it, removed a little chunk and then pressed the ends together, it should fit inside the port and, when released, it’s springiness should make it expand out to fit snugly. Yes?

Yesterday, I got 2 short pieces of 6″ and 4″ plastic sewer pipe and proceeded to saw rings 3/4″-1″ in width.


Then, I cut through the edge of the ring but, instead of removing a chunk, I instead heated the pipe and bent the ends down, forming ears that could be pinched together to reduce the size of the ring for insertion or removal.


Lulu sanded the edges so they wouldn’t snag the plastic screen.


Attached the screen using double-sided tape and then trimmed it to fit.


Squeezed the tabs together and tried her on for size:


Obviously the screen in these photos is not fine enough to keep jejenes out. But we didn’t want to have super-fine screen in all the time as it severely restricts airflow. So, the plan is, when we reach no-see-um country, we’ll simply lay a piece of the super-fine mesh screen over the existing screen and snap the ring back in place without taping the screen to the ring. That way it’ still very removable.

Ahhh… One less thing to lie awake at night trying to figure out.

Cost of 2 pieces of pipe: 40 pesos (about $3.20)
Cost of screen: free at a boater’s swap meet
Cost of tape: ?? we already had some on hand but will have to buy more.

And the beauty is, I still have enough pipe left to make at least another dozen frames for both sizes of portholes.


Advertisements

About sryoder

Steve & Lulu... retired. Had enough of the cold wet dreary fall/winter/spring in the Pacific Northwest. Bought a boat, fixed it up, sold our home and sailed to Mexico in November, 2010. Been here ever since except for occasional forays to the States (summer only, thank you) to visit the kids, parents and siblings. If you're looking for a sailing blog, this is the wrong place. This is a traveling, hunkering in, eating blog. Sailing is just how we get from place to place when we can't walk.
This entry was posted in Uncategorized. Bookmark the permalink.

8 Responses to 5/29/2011 – Porthole screens

  1. brilliant! good on ya! they look great. I'm enjoying your blog, hope y'all have a great bug free summer.

  2. Anonymous says:

    What a team you two are. You are just like your Dad, just tell him it can't be done and it will be done. The difference is you have LuAnn to help you wheras I am not much help on figureing stuff out. Love, Mom

  3. s/y Namaste says:

    What a splendid idea Steve! I am lucky as the screens are in place on Namaste. They are stuck hence non-removable though…Seeing what you did I'm impatiently waiting for your solution to water gauging ;-)Cheers,Wojtek

  4. Anonymous says:

    Good morning, Steve & Lulu: We have no-see-uns here in Florida and they raise welts on me like mosquitoes – that is why I don't send a whole lot of time outdoors sunbathing. Keep writing your blogs because I know that I really enjoy reading them So glad that you are enjoying your trip. Take care, good luck and my love to both of you – Nancy

  5. Anonymous says:

    What a clever solution! I'm looking forward to learning how you seal the companionway.EricSv Clementine

  6. I'm with Eric, above! Always looking for ways to screen my companionway on El Tesoro for summer jaunts to Desolation Sound…land of the giant mosquitoes. Love you guys…and you are SOOOOO resourceful!Samantha BrynerPS Took off for Sucia Island, engine over-heated so put up sails and went for it, by the time we got close to Fox Cove small craft warnings in place. Blew out head sail completely trying to get main down! Limped into port, got help catching a mooring then I replaced the impeller and we were able to motor back on the next day which was calm!!! Girl power rules!!!

  7. Anonymous says:

    The screens will work well for those nasty bees and hornets on Isla Carmen- beware Balandra Cove. I hope that's your last project so you can get out here again and enjoy the beautiful Sea of Cortez. Just keep an eye on that system brewing off mainland Mexico n heading our way. Yikes! http://www.passageweather.comLisa n NeilS/V Gypsy

  8. Anonymous says:

    You are amazingly creative!/Beverly

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s